We use cookies to make your experience better.
To comply with the new e-Privacy directive, you agree to the privacy policy and our use of cookies.
L.H. Dottie
Shop By
-
L.H. Dottie Lock Washers, Zinc Plated Steel, 1/4 in., Pack of 100
Split Lock Washers are manufactured with a trapezoidal cross section that deflects under load and can be used with or without a Hardened Flat Washer. They provide marginal resistance to vibration loosening and are ideal in applications where fasteners have a tendency to rotate or lose friction. Split Lock Washers are forged from hardened steel and zinc coated. They are covered by ASME B18.21.1. -
L.H. Dottie Lock Washers, Zinc Plated Steel, 1/2 in., Pack of 100
Split Lock Washers are manufactured with a trapezoidal cross section that deflects under load and can be used with or without a Hardened Flat Washer. They provide marginal resistance to vibration loosening and are ideal in applications where fasteners have a tendency to rotate or lose friction. Split Lock Washers are forged from hardened steel and zinc coated. They are covered by ASME B18.21.1. -
L.H. Dottie 3/8 x 4 in. Zinc Plated Steel Hex Head Lag Screws (50)
Lag Screws are heavy duty fasteners used to connect heavy lumber or other materials that bear a strenuous load. They are manufactured from low carbon steel and can be used with lag shields in a variety of masonry applications, such as concrete, brick, and mortar. Lag Screws can also be used where standard wood screws are too short or small. In some applications, a pilot hole may be pre-drilled to prevent splitting or snapping. ASME B18.2.1 cover the requirements for steel lag screws. -
L.H. Dottie K-Lath Metal Piercing Screws, Phillips Wafer Head, No. 8 x 1-5/8 in., Pack of 100
K-Lath Screws are metal-piercing screws capable of penetrating steel studs up to 20 gauge in thickness. They are a versatile fastener that can be utilized to attach metal lath to metal studs, or metal lath to wood studs. -
L.H. Dottie Fender Washer, Zinc Plated Steel, 5/16 x 1-1/4 in., Pack of 100
Fender Washers differ from standard Flat Washers in that their outside diameters are much larger in proportion to their center holes. With this design, a fender washercan be placed under the head of a bolt or nut, to help distribute forces applied when tightening, or to cover an oversized hole. -
L.H. Dottie Zinc Plated Steel Eye Bolt With Hex Nut, 1/4 x 3 in. Length
Eye Bolts are manufactured with a molded circular eye at the non-threaded end and NC rolled machine threads on the opposing end. They are the ideal fastener for light duty applications and are designed for attaching cables to surfaces. They are manufactured from low carbon, cold drawn steel wire and come furnished with hex nuts. -
L.H. Dottie No. 8 x 2 1/2 in. Fine Thread Bugle Head Phillips Drywall Screws (100)
Fine Thread Drywall Screws are used to secure drywall to 20-25 gauge steel. Their sharp, self piercing point allows for easy penetration, and their fine threads provide a strong hold. They feature a countersunk bugle head that tapers down into the drywall after installation to provide a clean, finished look. They are manufactured to the ASTM C1002 standard and are finished in a black phosphate coating. -
L.H. Dottie Snap-In Cable Connector, Thermoplastic, for Non-Metallic Cable, 1/2 in.
The DRC50 connector is used to connect non-metallic sheathed cable to a steel outlet box or metal enclosure. It requires no tools for installation and easily snaps into a 1/2'' knockout. -
L.H. Dottie Straight Ceiling Wire, Galvanized Steel, 12 ga., 8 ft.
Dottie ceiling wires are installed with Dottie telescoping pole tool and Dottie flat hanger screws. -
L.H. Dottie Pre-Tied Ceiling Wire With Pin and Clip, Galvanized Steel, 12 ga., 6 ft. L
Dottie pre-tied ceiling wires are installed with low-velocity powder actuated tools in poured concrete deck. Includes 1-1/4 in. pin and clip.
