We use cookies to make your experience better.
To comply with the new e-Privacy directive, you agree to the privacy policy and our use of cookies.
L.H. Dottie
Shop By
-
L.H. Dottie Cat-A-Pillar Non-Metallic Wiring Device Spacer
Installs quickly on single or multi-gang boxesReusable and can be used as a shim or a plastic washer to straighten crooked devicesLow density polyethyleneNon-conductive -
L.H. Dottie Tool for Drop-In Anchor, 1/4-20
AT tool must be used for proper installationSold separately from DA/DAS anchors -
L.H. Dottie 5/16 in. L x 5/16 in. W T59 Black Plastic Insulated Steel Staples (300)
T59 insulated staples for use with T59 wire and cable tacker. -
L.H. Dottie 1/4 x 1-1/2 Zinc Plated Steel Hex Head Cap Screws With Partial Thread
Grade 5 Hex Cap Screws are made from carbon steel and are used in applications where medium strength is necessary, typically those where controlled clamp force and high loads are required. These screws can be screwed into internally tapped holes or used with a nut. Grade 5 Hex Cap Screws should always be used with a hardened washer under the turned component. SAE J429 covers the material and performance requirements of Grade 5 Hex Cap Screws and ASME B18.2.1 covers the dimensional requirements. -
L.H. Dottie Hi-Low Thread Hex Head Slotted Concrete Anchor, 1/4 x 1-1/4 in.
Dottie's concrete anchors are faster to install than most steel anchors, yet have significant load capacities. One tool drills the hole and sets the anchor without the need to remove from the drill chuck. They have the added advantage of close-to-edge fastening without potential breakout. These anchors work in poured concrete, prestressed concrete, cinder block and brick and mortar and can be loosened for adjustment or removed. CAUTION: Always wear eye protection! -
L.H. Dottie Zinc Plated Full-Thread Wedge Anchors, 1/4 x 1-3/4 in., Pack of 100
Allow for fixture thickness plus one anchor diameter for the nut and washer thickness when selecting a length. -
L.H. Dottie Self Drilling Screws, Phillips Pan Head, Zinc Plated Steel, No. 8 x 3/4 in.
Self-Drilling Screws are manufactured from cold-heading steel and feature a 2 drill point. The unique tip design allows them to drill, tap, and fasten metal to metal objects in one operation, without the need to pre-drill. This creates the optimal drill performance and thread forming experience. The most common applications are used on metal to metal, but they can also be used in a wide variety of other applications. IFI-113 and ASTM C954 cover the material and performance requirements for steel self-drilling screws. -
L.H. Dottie 10 32 x 3/4 in. Zinc Plated Steel Round Head Phillips/Slotted Machine Screws (100)
Machine Screws are uniformly threaded screws designed to be fastened into tapped holes, or used in conjunction with nuts to join two or more assemblies together. Typical applications for machine screws include fastening components of tools, appliances, machines, and electronic devices. ASME B18.3 covers the general requirements for the dimensions and performance of Steel Machine Screws. -
L.H. Dottie 3/8 x 3 in. Zinc Plated Steel Hex Head Tap Bolts (100)
Hex Head Tap Bolts can be fastened into internally tapped holes or used with a nut to pull assemblies together over a long length. For adjustment applications, they may be used with jam nuts to secure the assembly in place. They are manufactured to the IFI-199 standard. -
L.H. Dottie Zinc Plated Steel Hex Head Tap Bolts, 1/4 x 1-1/4 in. L, Pack of 100
Hex Head Tap Bolts can be fastened into internally tapped holes or used with a nut to pull assemblies together over a long length. For adjustment applications, they may be used with jam nuts to secure the assembly in place. They are manufactured to the IFI-199 standard.
