We use cookies to make your experience better.
To comply with the new e-Privacy directive, you agree to the privacy policy and our use of cookies.
L.H. Dottie
Shop By
-
L.H. Dottie Zamac Anchor, Hammer Screw With Carbon Steel Screw Drive, 1/4 x 1-1/2 in. Length
The Zamac Hammer Screw174 is a unique, one-step drive anchor featuring a Phillips head and screw thread. Designed to provide a removable anchor with 40% higher tension load capacities when installed in concrete. Use for concrete, block, brick or stone. Not recommended for ceiling applications. -
L.H. Dottie No. 14 x 1 in. Zinc Plated Steel Hex Washer Head Self Drilling Screws (100)
Self-Drilling Screws are manufactured from cold-heading steel and feature a 2 drill point. The unique tip design allows them to drill, tap, and fasten metal to metal objects in one operation, without the need to pre-drill. This creates the optimal drill performance and thread forming experience. The most common applications are used on metal to metal, but they can also be used in a wide variety of other applications. IFI-113 and ASTM C954 cover the material and performance requirements for steel self-drilling screws. -
L.H. Dottie Handi-Foam Expanding Sealant, 12 oz.
Improves Building Efficiencies By Sealing Penetrations Improves Outdoor Air Quality 12 ounce Can -
L.H. Dottie Stranded 12 AWG Ground Pigtail with Flange Hex-Head Combo Ground Screw, 8 in. L, Green
Grounding Pigtails are used to ground junction boxes, multi-gang receptacle boxes and power distribution boxes. They come preassembled with 12 ga stranded copper wire and a 1/4'' leader point ground screw. -
L.H. Dottie Flat Washer, Zinc Plated Steel, No. 10, Pack of 100
Flat Washers are used to increase the surface area of fasteners, in order to evenly distribute the force applied when tightening them to a surface. They are also used to prevent loosening due to vibration, to stop the bolt or screw from pulling through, and act as spacers.They are manufactured from steel and zinc-plated and are manufactured to ASME B18.21.1 standard. -
L.H. Dottie Stainless Steel Fender Washers, 1/4 x 1 in., Pack of 100
Stainless Steel Fender Washers differ from Stainless Steel Flat Washers in that their outside diameters are much larger in proportion to their center holes. With this design a fender washer can be placed under the head of a bolt or nut to help distribute forces applied when tightening or to cover an oversized hole. -
L.H. Dottie Fender Washer, Zinc Plated Steel, 3/8 x 1-1/2, Pack of 100
Fender Washers differ from standard Flat Washers in that their outside diameters are much larger in proportion to their center holes. With this design, a fender washercan be placed under the head of a bolt or nut, to help distribute forces applied when tightening, or to cover an oversized hole. -
L.H. Dottie 5/16 x 1 in. Zinc Plated Steel Hex Head Cap Screws With Partial Thread
Grade 5 Hex Cap Screws are made from carbon steel and are used in applications where medium strength is necessary, typically those where controlled clamp force and high loads are required. These screws can be screwed into internally tapped holes or used with a nut. Grade 5 Hex Cap Screws should always be used with a hardened washer under the turned component. SAE J429 covers the material and performance requirements of Grade 5 Hex Cap Screws and ASME B18.2.1 covers the dimensional requirements. -
L.H. Dottie Ground Screws, Green, 10 32 x 3/8 in., Leader Point, Phillips/Square Head
Ground Screws feature a leader point for quick installation and are used to ground wires in electrical junction boxes. They can also be used with pigtails and are plated green for indentification purposes. -
L.H. Dottie No. 10 x 1 1/4 in. Zinc Plated Steel Pan Head Phillips Self Drilling Screws (100)
Self-Drilling Screws are manufactured from cold-heading steel and feature a 2 drill point. The unique tip design allows them to drill, tap, and fasten metal to metal objects in one operation, without the need to pre-drill. This creates the optimal drill performance and thread forming experience. The most common applications are used on metal to metal, but they can also be used in a wide variety of other applications. IFI-113 and ASTM C954 cover the material and performance requirements for steel self-drilling screws.
