We use cookies to make your experience better.
To comply with the new e-Privacy directive, you agree to the privacy policy and our use of cookies.
Caddy (nVent)
Shop By
-
Caddy (nVent) Multi Function Clip For 1/4 in. Rod or No. 12 Wire
Supports No. 10-24 and 1/4-20 Threaded Bridle RingsSupports 4 or 4-11/16 in. Electrical Box -
Caddy (nVent) Spring Steel Hammer On Side Mount Flange Clip for 1/8 thru 1/4 in. Flange
Provides a Portable HoleFits Most Beams and Bulb TeesInstalls With Just a Hammer -
Caddy (nVent) CADDY174 Electrogalvanized Steel 4 in. Dia. Threaded Bridle Ring With 1/4 in. Metal Screw
When combined with other CADDY174Fasteners, bridle rings can be loated on C-purlins, Z-purlins, acoustical T-grid, beam flanges up to 3/4 in., concrete or drop wire. Not recommended for high performance cables--see CADDY174 CABLECAT series. -
Caddy (nVent) H-MSM Series Side Mount Conduit to Flange Clip For 1 in. EMT Conduit and 1/8 to 1/4 in. Flange, Spring Steel
Available With Conduit Clip Bottom Mounted or Side MountedAvailable For EMT, Rigid and Aluminum ConduitRequires Only a Hammer to InstallWill Pivot Thru 360 Degrees -
Caddy (nVent) Strut, 7/8 in, Steel, 14 to 21-1/2 in L, 14 to 21-1/2 L x 1-5/8 W in. Channel, 1-5/8 in. W
Captive threaded nuts enable fastening to threaded rod supports without loose partsTelescopes to the desired length and is locked in place by snapping closed a spring retainer clipStandard strut profile runs the entire length of the part, allowing most standard fittings to be placed anywhere between the rodsIntegrated ruler displays space between hanger rods in inches and centimetersSupports up to seven 2 (50 DN) conduits, six 2 (50 DN) water filled pipes at 10' (3 m) spacing, or up to 18148 (450 mm) cable trayConduit can be supported on the top and bottom, eliminating the need for double sided strutConduit and pipe can be placed directly on the strut profile, saving vertical space in buildings with limited room for installation -
Caddy (nVent) CADDY174 GLIDER Electrical Box Attachment With No. 10 Hole
Attaches Electrical Boxes to the TSGB With a Single Screw, Without Tools and Without Need For DisassemblyAllows For Easy Repositioning of Electrical BoxesIdeal For Pre-Fab Assemblies -
Caddy (nVent) Telescoping Screw Gun Support Bracket, Pre-Galvanized Steel, For 1-1/2, 2-1/8 and 2-1/2 in. Deep Box
Can mount multiple boxesNotched and marked for easy identification and bendingImproved design with stamped inch markings and pilot holes accelerates precise box conduit mounting between studsPilot holes allow easy box attachment with screwdriverRequires only a screw gun to installCan be mounted to face or inside of studAdjustable for non-standard stud spacingInterlocking tab prevents accidental assemblyUnique, one-piece, break apart design -
Caddy (nVent) CADDY174 Speed Link SLK With Y Toggle, Wire Rope Diameter 1.5 mm, Length 9.9 ft., Y-Length 11.8 in.
Complete system includes wire, locking device and two pre-assembled toggle end fittings. Attaches to clearance holes in a variety of structures or hanging devices. Ideal for supporting lighting fixtures. -
Caddy (nVent) CADDY174 SPEED LINK Wire Spool, 1.5mm Wire, Length 164 ft.
Wire rope constructed from seven bundles of seven strands each of steel aircraft wire.
