We use cookies to make your experience better.
To comply with the new e-Privacy directive, you agree to the privacy policy and our use of cookies.
Caddy (nVent)
Shop By
-
Caddy (nVent) CADDY174 CAT HP J-Hook Assembled to Multi-Function Clip, 1/4 in. Rod or 12 thru 8 Wire, 30 lb. Load Rating
Quick Attachment to Threaded Rod or WireProvides Optimal Support For High-Performance Data Cable, Up to and Including Cat 5e, Cat 6, Cat 6A, Cat 7 and Fiber OpticProvides Superior Fill Capacity and Load Rating Over Most Other Non-Continuous Cable Support AlternativesRounded Edges on J-Hooks Provide Proper Bend Radius Support For High Performance Data CablesCost-Effective Alternative to Expensive Cable TrayComplies With EN 50174-2Meets ISO/IEC 14763-2, TIA 568-C and TIA 569-CNon-Continuous Supports May Not Exceed Spacing of 5 ft. (1.5m) Per TIA 569-C.9.7Cable Capacity is Calculated Based On a 70% Fill Rate -
Caddy (nVent) CADDY174 CABLECAT J-Hook, Steel, 3/4 in. Dia.
J-Hook that accepts up to 16 4-pair UTP CAT 5e or 2- strand fiber optic cable, or 10 CAT 6.cULus174 Listed and complies with NEC174 and TIA requirements for structured cabling systems -
Caddy (nVent) Steel M CPNAM Series Conduit to Deck Angle Bracket For 1/2 or 3/4 in. EMT Conduit
Supports Conduit or Pipe 1-1/2 in. (38mm) Under Roof Decking to Prevent Potential Damage From Nails or ScrewsMeets the Requirements of NEC Section 300.4(E) -
Caddy (nVent) B18 Combination Box/Conduit Hanger With 1/4 in. Plain Hole for 3/8 in. EMT Conduit, Spring Steel
One Rivited Assembly For Electrical Box and Conduit SupportEliminates Need For Offset Bending Conduit66% Less Drop Wires (Rod/Wire Application)Delivers With NEC and CEC ComplianceFor Single and Multiple Runs of ConduitNEC 300.11 Requires Dedicated Drop Wire/Rod and EC311 -
Caddy (nVent) MATA Conduit to T-Grid Clip For 3/8 in. EMT Conduit or 14 2 to 12 3 MC/AC Cable, Spring Steel
Provides a Method of Supporting Conduit and Outlet Boxes Above Acoustical Tee BarAvailable For Both Horizontal and Vertical SupportNo Installation Tools Required For Basic ClipEliminates Need For Offset Bending ConduitNo Load Rating, For Positioning OnlyAdditional Support Required Per NEC 300.11 -
Caddy (nVent) B18 Combination Box/Conduit Hanger With 1/4 in. Plain Hole for 1 in. EMT Conduit, Spring Steel
One Rivited Assembly For Electrical Box and Conduit SupportEliminates Need For Offset Bending Conduit66% Less Drop Wires (Rod/Wire Application)Delivers With NEC and CEC ComplianceFor Single and Multiple Runs of ConduitNEC 300.11 Requires Dedicated Drop Wire/Rod and EC311 -
Caddy (nVent) H-PSM Series Conduit to Flange Clip for 3/4 in. EMT Conduit and 1/8 to 1/4 in. Flange, Spring Steel
Requires Only a Hammer to InstallAvailable For EMT, Rigid and Aluminum ConduitWill Pivot Thru 360 DegreesNOTE: Indicated Loads Are Ultimate and Should Not be Combined -
Caddy (nVent) Electrogalvanized Steel SN Series 3/8 in. Threaded Rod Nuts (100)
Allows Side Mounting of Nut to Threaded RodReduces the Need For Threading Compared to Standard Nuts and WashersIdeal For Retrofit Projects, Such as Trapeze InstallationsWorks With Slightly Damaged Threads and Minor Burrs on the Threaded RodReduces Installation Time Up to 50%For Use on Plain and Electro Zinc Plated Hardware Only -
Caddy (nVent) Electrogalvanized Steel 1-Piece Strut Clamp For 0.34 to 0.71 in. O.D. Cable or 1/2 in. EMT Conduit
One-Piece Cable/Conduit Clamp With Protective BootNo Screws or Bolts to DropRequires Only a Screwdriver or Nutdriver for InstallationFits Into Open Side of Strut Channel
