We use cookies to make your experience better.
To comply with the new e-Privacy directive, you agree to the privacy policy and our use of cookies.
Caddy (nVent)
Shop By
-
Caddy (nVent) Electrogalvanized Steel 1-Piece Strut Clamp For 0.57 to 0.92 in. O.D. Cable, 3/4 in. EMT or 1/2 in. Rigid Conduit
One-Piece Cable/Conduit Clamp With Protective BootNo Screws or Bolts to DropRequires Only a Screwdriver or Nutdriver for InstallationFits Into Open Side of Strut Channel -
Caddy (nVent) Cable Snap Clip For 0.468 to 0.562 in. O.D. Cable and 5/16 thru 1/2 in. Flange, Spring Steel
Supports cable from 1/16 - 1/2 in. flangeWorks effectively with MC and AC cable dimensions 3/8 - 1-1/4 in. and low voltage cables from 7/32 in. and upSnap clips attach to beams without tools within seconds -
Caddy (nVent) Cable Snap Clip For 0.468 to 0.562 in. O.D. Cable and 3/16 thru 9/32 in. Flange, Spring Steel
Supports cable from 1/16 - 1/2 in. flangeWorks effectively with MC and AC cable dimensions 3/8 - 1-1/4 in. and low voltage cables from 7/32 in. and upSnap clips attach to beams without tools within seconds -
Caddy (nVent) CADDY174 Fixed Strut Support, Steel, 12-1/2 in. L
Provides superior support for pipe, conduit, duct, cable tray and equipment. Foam bottom offers low abrasion interface for better roof membrane protection. Compatible with roof surfaces including single ply, bituminous, metal and spray foam. Provides superior load distribution, even with varying rooftop surfaces. Ready to use out of the box, saving installation time and labor. Multiple sizes and load ratings offer the ability to tailor the solution to the application. Easy to transport to the roof. Hot-dip galvanized and UV stabilized for long lasting performance. -
Caddy (nVent) Pre-Galvanized Steel Box Support Bracket With Legs For Metal Studs
Support leg reduces movement of box in wallBox of 100 -
Caddy (nVent) MC/AC Cable Support Bracket With Rod/Wire Clip, Steel
Neatly isolates, supports and secures MC/AC cables. Properly spaces MC/AC cable to help eliminate bundling and NEC and CEC derating issues. Results in a neat and workmanlike installation. -
Caddy (nVent) Hammer-On Flange Clip, Bottom Mount For 1/4 in. Rod, 1/8 thru 1/4 in. Flange, Spring Steel
Bottom-mount hammer-on flange clips are used to support pipe from beam flanges and require only a hammer to install. -
Caddy (nVent) Spring Steel Cable Support to Stud For 14 2 to 12 3 MC/AC or Non Metallic Cable (7/16 to 9/16 in. O.D.)
Provides Secure Support of NMC or MC/AC to Metal or Wood Stud in SecondsOne Fastener, Four ApplicationsDelivers Compliance With NEC 300.4(d), CEC 12-618 and CEC 12-510No Installation Tools Required -
Caddy (nVent) CADDY174 Screw On Conduit Support For 1-1/2 in. Deep Box
Easily Locate the Fastener on the Stud, Keeping Your Conduit in Line With Box Knockout and H-Series BracketsEliminates Offset Bending of ConduitCompliant With NEC Article 358.30(A), Which Requires Conduit Support Within 36 in. of an Electrical BoxCompliant With CEC Rule 12-1404, Which Requires Conduit Support Within 1m of an Electrical BoxCompliant With CEC Rule 12-618, Which Requires Support of Armoured Cable Within 300mm (12 in.) of an Electrical Box -
Caddy (nVent) Bolt Close Conduit/Pipe Clamp, Retained Bolt and Built-In Nut, Size 2, For 1 in. Rigid/EMT, 1/4 in. Hole, Steel
Retained Bolt and Built-In Nut Means There Are Less Parts to Handle or DropCombo Head Bolt Ready to Work With Any Tool Handy--Slotted, Hex, No. 3 Phillips or No. 2 Robertson
