We use cookies to make your experience better.
To comply with the new e-Privacy directive, you agree to the privacy policy and our use of cookies.
L. H. Dottie
Shop By
-
L. H. Dottie Zamac Anchor, Hammer Screw With Carbon Steel Screw Drive, 1/4 x 1 in. Length
The Zamac Hammer Screw174 is a unique, one-step drive anchor featuring a Phillips head and screw thread. Designed to provide a removable anchor with 40% higher tension load capacities when installed in concrete. Use for concrete, block, brick or stone. Not recommended for ceiling applications. -
L. H. Dottie Coarse Thread Bugle Head Phillips Drywall Screws/Wood Rockets, Yellow Zinc, No. 6 x 1-1/4 in.
Coarse Thread Drywall Screws are manufactured with a single lead point and spaced threads that create for a strong hold when fastening drywall or sheetrock to wood framing. They feature a countersunk bugle head that tapers down in to the drywall after installation to provide a clean, finished look. They are covered under ASTM C954 and ASTM C1002 guidelines. -
L. H. Dottie Nylon Wall Driller Anchor, No. 6
Used only in drywall, this Dottie anchor has better pullout and shear values than plastic anchors. Installed by inserting Phillips or square drive bit into the anchor and driving it into the drywall until flush. Use the same bit to insert the proper sheet metal screw to mount the fixture. The anchor is easy to spot and will not break out the backing of the drywall. No drill bit needed. -
L. H. Dottie Full-Thread Wedge Anchors, 3/8 x 5 in. Zinc Plated, Pack of 50
Allow for fixture thickness plus one anchor diameter for the nut and washer thickness when selecting a length. -
L. H. Dottie Full-Thread Wedge Anchors, 3/8 x 3-3/4 in. Zinc Plated, Pack of 50
Allow for fixture thickness plus one anchor diameter for the nut and washer thickness when selecting a length. -
L. H. Dottie 1/2 x 5-1/2 in. Zinc Plated Full-Thread Wedge Anchors (50)
Allow for fixture thickness plus one anchor diameter for the nut and washer thickness when selecting a length. -
L. H. Dottie Self Drilling Screw, Phillips Wafer Head, Zinc Plated Steel, No. 8 x 3/4 in., Pack of 100
Self-Drilling Screws are manufactured from cold-heading steel and feature a 2 drill point. The unique tip design allows them to drill, tap, and fasten metal to metal objects in one operation, without the need to pre-drill. This creates the optimal drill performance and thread forming experience. The most common applications are used on metal to metal, but they can also be used in a wide variety of other applications. IFI-113 and ASTM C954 cover the material and performance requirements for steel self-drilling screws. -
L. H. Dottie No. 6 x 1/2 in. Zinc Plated Steel Pan Head Phillips Self Drilling Screws (100)
Self-Drilling Screws are manufactured from cold-heading steel and feature a 2 drill point. The unique tip design allows them to drill, tap, and fasten metal to metal objects in one operation, without the need to pre-drill. This creates the optimal drill performance and thread forming experience. The most common applications are used on metal to metal, but they can also be used in a wide variety of other applications. IFI-113 and ASTM C954 cover the material and performance requirements for steel self-drilling screws. -
L. H. Dottie Hex Washer Head Self Drilling Screws, Zinc Plated Steel, No. 12 x 2 in.
Self-Drilling Screws are manufactured from cold-heading steel and feature a 2 drill point. The unique tip design allows them to drill, tap, and fasten metal to metal objects in one operation, without the need to pre-drill. This creates the optimal drill performance and thread forming experience. The most common applications are used on metal to metal, but they can also be used in a wide variety of other applications. IFI-113 and ASTM C954 cover the material and performance requirements for steel self-drilling screws.
