We use cookies to make your experience better.
To comply with the new e-Privacy directive, you agree to the privacy policy and our use of cookies.
L. H. Dottie
Shop By
-
L. H. Dottie Flat Washer, Zinc Plated Steel, No. 8, Pack of 100
Flat Washers are used to increase the surface area of fasteners, in order to evenly distribute the force applied when tightening them to a surface. They are also used to prevent loosening due to vibration, to stop the bolt or screw from pulling through, and act as spacers.They are manufactured from steel and zinc-plated and are manufactured to ASME B18.21.1 standard. -
L. H. Dottie Stainless Steel Fender Washers, 3/8 x 1-1/2, Pack of 100
Stainless Steel Fender Washers differ from Stainless Steel Flat Washers in that their outside diameters are much larger in proportion to their center holes. With this design a fender washer can be placed under the head of a bolt or nut to help distribute forces applied when tightening or to cover an oversized hole. -
L. H. Dottie Snap-In Cable Connector, Thermoplastic, for Non-Metallic Cable, 3/4 in.
The DRC75 connector is used to connect non-metallic sheathed cable to a steel outlet box or metal enclosure. They require no tools for installation and easily snap into a 3/4'' knockout. -
L. H. Dottie Pre-Tied Ceiling Wire With Pin and Clip, Galvanized Steel, 12 ga., 8 ft. L
Dottie pre-tied ceiling wires are installed with low-velocity powder actuated tools in poured concrete deck. Includes 1-1/4 in. pin and clip. -
L. H. Dottie Zinc Rich Galvanize Coating, 13 oz. can.
The 7007 features a zinc-rich formula that is designed for permanent protection and corrosion prevention. It can be easily sprayed, brushed, or dipped onto any metal surface. -
L. H. Dottie Side Mount Fluorescent Fixture Hanger
Side Mount Fluorescent Fixture Hangers are used in conjunction with S-Hooks and Jack Chain. They provide an easy way of supporting industrial class fluorescent light fixtures. -
L. H. Dottie 3/8 x 1 in. Zinc Plated Steel Hex Head Cap Screws With Partial Thread
Grade 5 Hex Cap Screws are made from carbon steel and are used in applications where medium strength is necessary, typically those where controlled clamp force and high loads are required. These screws can be screwed into internally tapped holes or used with a nut. Grade 5 Hex Cap Screws should always be used with a hardened washer under the turned component. SAE J429 covers the material and performance requirements of Grade 5 Hex Cap Screws and ASME B18.2.1 covers the dimensional requirements. -
L. H. Dottie 8 x 1/2 in. Pan Head Phillips/Slotted (2 Way) Sheet Metal Screws
Sheet Metal Screws are a versatile fastener with specially hardened spaced threads and sharp points, and are capable of tapping their own internal threads. Typical applications for Sheet Metal Screws include fastening light metal sheets, wood, and plastic. They are manufactured with case hardened steel and finished with a zinc plating. ASME B18.3 covers the general requirements for the dimensions and performance of Steel Sheet Metal Screws. -
L. H. Dottie Safety Plate/Nail Plate, 16 ga. Steel, 5 L x 1-3/4 in. W (Box of 100)
Steel safety plates are affixed to the face of 2x4 members to protect utility pipes and to prevent nails from penetrating into hidden live wires (NMC cable) which may be running through notches or through the drilled holes in the stud. -
L. H. Dottie Red Tapered Plastic Anchor With Collar in Invincibox8482 Screw Size 6-8-10, Length 7/8 in.
Drill a hole into drywall, concrete, brick or block and insert anchor. The screw is then installed through the fixture into the anchor. Used for light duty work.
