We use cookies to make your experience better.
To comply with the new e-Privacy directive, you agree to the privacy policy and our use of cookies.
Caddy (nVent)
Shop By
-
Caddy (nVent) Twist Clip With Wing Nut For 15/16 in. T-Grid, Spring Steel, 9/16 in. Screw Length
T-grid twist clips support electrical fixtures from acoustical T-grid. 6WN wing nut included. -
Caddy (nVent) CADDY174 Electrogalvanized Steel 1-1/4 in. Dia. Threaded Bridle Ring With 1/4 in. Metal Screw
When combined with other CADDY174Fasteners, bridle rings can be loated on C-purlins, Z-purlins, acoustical T-grid, beam flanges up to 3/4 in., concrete or drop wire. Not recommended for high performance cables--see CADDY174 CABLECAT series. -
Caddy (nVent) CADDY174 Electrogalvanized Steel 2 in. Dia. Threaded Bridle Ring With Metal Screw, No. 10
When combined with other CADDY174Fasteners, bridle rings can be loated on C-purlins, Z-purlins, acoustical T-grid, beam flanges up to 3/4 in., concrete or drop wire. Not recommended for high performance cables--see CADDY174 CABLECAT series. -
Caddy (nVent) EM-P Series Conduit to Flange Clip for 1 in. EMT or 3/4 in. Rigid Conduit and 1/8 to 1/4 in. Flange, Spring Steel
Requires Only a Hammer to InstallAvailable For EMT, Rigid, IMT and Aluminum ConduitWill Pivot Thru 360 Degrees -
Caddy (nVent) Snap Close Conduit/Pipe Clamp With Plain Hole For 1 in. EMT or Rigid Conduit
May be Used For Either Vertical or Horizontal InstallationsHelps to Guide Alignment With Electrical Box KnockoutsFinger Closure -
Caddy (nVent) Telescoping Between Stud Rigid Box Support For 16 to 24 in., Stud Spacing and 4 or 4 11/16 in. Square Box, Pre-Galvanized Steel
Accommodates Up to 6-Gang Box in 16 in. Stud Spacing or Up to 10-Gang in 24 in. Stud SpacingWill Support Four Electrical Boxes in 24 in. Stud SpacingOpen Design Allows a Variety of Positions For Box LocationEasy to Adjust After the Electrical Box is InstalledFor Use With 4 in. Square and 4-11/16 in. Boxes and Mud RingsUnique One-Piece Break-Apart Design -
Caddy (nVent) Electrogalvanized Steel 1-Piece Strut Clamp For 0.10 to 0.63 in. O.D. Cable
One-Piece Cable/Conduit Clamp With Protective BootNo Screws or Bolts to DropRequires Only a Screwdriver or Nutdriver for InstallationFits Into Open Side of Strut Channel -
Caddy (nVent) Electrogalvanized Steel 1-Piece Strut Clamp For 3.25 to 4.00 in. O.D. Cable or 3 1/2 in. EMT or Rigid Conduit
One-Piece Cable/Conduit Clamp With Protective BootNo Screws or Bolts to DropRequires Only a Screwdriver or Nutdriver for InstallationFits Into Open Side of Strut Channel -
Caddy (nVent) Electrogalvanized Steel 1-Piece Strut Clamp For 2.38 to 2.88 in. O.D. Cable or 2 1/2 in. EMT or Rigid Conduit
One-Piece Cable/Conduit Clamp With Protective BootNo Screws or Bolts to DropRequires Only a Screwdriver or Nutdriver for InstallationFits Into Open Side of Strut Channel
