We use cookies to make your experience better.
To comply with the new e-Privacy directive, you agree to the privacy policy and our use of cookies.
L. H. Dottie
Shop By
-
L. H. Dottie Zinc Plated Steel Hex Head Tap Bolts, 1/4 x 1 in. L, Pack of 100
Hex Head Tap Bolts can be fastened into internally tapped holes or used with a nut to pull assemblies together over a long length. For adjustment applications, they may be used with jam nuts to secure the assembly in place. They are manufactured to the IFI-199 standard. -
L. H. Dottie 3/8 x 2 in. Zinc Plated Steel Hex Head Lag Screws (100)
Lag Screws are heavy duty fasteners used to connect heavy lumber or other materials that bear a strenuous load. They are manufactured from low carbon steel and can be used with lag shields in a variety of masonry applications, such as concrete, brick, and mortar. Lag Screws can also be used where standard wood screws are too short or small. In some applications, a pilot hole may be pre-drilled to prevent splitting or snapping. ASME B18.2.1 cover the requirements for steel lag screws. -
L. H. Dottie Hex Head Lag Screws, Zinc Plated Steel, 1/4 x 2-1/2 in., Pack of 100
Lag Screws are heavy duty fasteners used to connect heavy lumber or other materials that bear a strenuous load. They are manufactured from low carbon steel and can be used with lag shields in a variety of masonry applications, such as concrete, brick, and mortar. Lag Screws can also be used where standard wood screws are too short or small. In some applications, a pilot hole may be pre-drilled to prevent splitting or snapping. ASME B18.2.1 cover the requirements for steel lag screws. -
L. H. Dottie Hex Washer Head Slotted Sheet Metal Screws, Zinc Plated Steel, No. 12 x 2 in.
Sheet Metal Screws are a versatile fastener with specially hardened spaced threads and sharp points, and are capable of tapping their own internal threads. Typical applications for Sheet Metal Screws include fastening light metal sheets, wood, and plastic. They are manufactured with case hardened steel and finished with a zinc plating. ASME B18.3 covers the general requirements for the dimensions and performance of Steel Sheet Metal Screws. -
L. H. Dottie Finished Hex Nuts, 1/4-20, Zinc Plated Steel, Pack of 100
Zinc Plated Hex Nuts are manufactured from grade 2 carbon steel and are used to connect both metal and wood components. They are also used in conjunction with bolts, screws, studs, threaded rod and any other fastener that has machine screw threads. They are manufactured under the SAE J995-2017 standard. -
L. H. Dottie Zinc Plated Ground Clip, Carbon Steel
Grounding Clips are used to connect the grounding conductor of non-metallic sheathed cable to outlet boxes, or for connecting the grounding jumper from a receptacle to an outlet. They are intended to be installed on the top edge of a box to hold 10, 12 or 14 AWG copper wire. They can also be used to hold 10 or 12 AWG aluminum grounding conductors against the side wall. -
L. H. Dottie Flat Washers, Stainless Steel, 1/4 in., Pack of 100
Stainless Steel Flat Washers are used to increase the surface area of fasteners, in order to evenly distribute the force applied when tightening them to a surface. They are also used to prevent loosening due to vibration, to stop the bolt or screw from pulling through, and act as spacers. They are manufactured from 18-8 stainless steel and are covered by the ASME B18.21.1 standard. -
L. H. Dottie Flat Washer, Zinc Plated Steel, 3/4 in., Pack of 25
Flat Washers are used to increase the surface area of fasteners, in order to evenly distribute the force applied when tightening them to a surface. They are also used to prevent loosening due to vibration, to stop the bolt or screw from pulling through, and act as spacers.They are manufactured from steel and zinc-plated and are manufactured to ASME B18.21.1 standard. -
L. H. Dottie Fender Washer, Zinc Plated Steel, 1/2 x 1-1/2, Pack of 100
Fender Washers differ from standard Flat Washers in that their outside diameters are much larger in proportion to their center holes. With this design, a fender washercan be placed under the head of a bolt or nut, to help distribute forces applied when tightening, or to cover an oversized hole. -
L. H. Dottie Fine Thread Drywall Screw, Bugle Head Phillips, Black Oxide, No. 6 x 1-1/4 in., Pack of 100
Fine Thread Drywall Screws are used to secure drywall to 20-25 gauge steel. Their sharp, self piercing point allows for easy penetration, and their fine threads provide a strong hold. They feature a countersunk bugle head that tapers down into the drywall after installation to provide a clean, finished look. They are manufactured to the ASTM C1002 standard and are finished in a black phosphate coating.
