We use cookies to make your experience better.
To comply with the new e-Privacy directive, you agree to the privacy policy and our use of cookies.
L.H. Dottie
Shop By
-
L.H. Dottie Three-in-One Roof Jack, 1-1/2 to 3 in.
3 in 1 Roof Jacks are an adjustable rubber roof flashing that accommodates service entrance conduit or ventilation pipe in a variety of sizes. It is manufactured with an elastomer collar that has been tested for ultraviolet, ozone and weather resistance. -
L.H. Dottie 10 32 x 1 in. Zinc Plated Steel Round Head Phillips/Slotted Machine Screws (100)
Machine Screws are uniformly threaded screws designed to be fastened into tapped holes, or used in conjunction with nuts to join two or more assemblies together. Typical applications for machine screws include fastening components of tools, appliances, machines, and electronic devices. ASME B18.3 covers the general requirements for the dimensions and performance of Steel Machine Screws. -
L.H. Dottie Stainless Steel Hex Head Cap Screws With Partial Thread, 1/4 x 1/2 in., Pack of 100
Stainless Steel Hex Head Tap Bolts are used in non-critical applications or where corrosion resistance is the primary concern. They are used to pull assemblies together and are manufactured with 304 stainless steel. It is recommended that Stainless Steel Hex Head Tap Bolts be used with stainless steel nuts and washers. -
L.H. Dottie Hex Washer Head Slotted Sheet Metal Screws, Zinc Plated Steel, No. 10 x 3/4 in.
Sheet Metal Screws are a versatile fastener with specially hardened spaced threads and sharp points, and are capable of tapping their own internal threads. Typical applications for Sheet Metal Screws include fastening light metal sheets, wood, and plastic. They are manufactured with case hardened steel and finished with a zinc plating. ASME B18.3 covers the general requirements for the dimensions and performance of Steel Sheet Metal Screws. -
L.H. Dottie 7-1/2 in. Solid 12 AWG Grounding Pigtail with Hex-Head Combo Ground Screw, Green
Solid copper wire1/4 in. hex/slotted/phillips/square with (leader point) -
L.H. Dottie Flat Washer, Zinc Plated Steel, No. 6, Pack of 100
Flat Washers are used to increase the surface area of fasteners, in order to evenly distribute the force applied when tightening them to a surface. They are also used to prevent loosening due to vibration, to stop the bolt or screw from pulling through, and act as spacers.They are manufactured from steel and zinc-plated and are manufactured to ASME B18.21.1 standard. -
L.H. Dottie Flat Washer, Zinc Plated Steel, 1/2 in., Pack of 50
Flat Washers are used to increase the surface area of fasteners, in order to evenly distribute the force applied when tightening them to a surface. They are also used to prevent loosening due to vibration, to stop the bolt or screw from pulling through, and act as spacers.They are manufactured from steel and zinc-plated and are manufactured to ASME B18.21.1 standard. -
L.H. Dottie Pre-Tied Ceiling Wire With Pin and Clip, Galvanized Steel, 12 ga., 12 ft. L
Dottie pre-tied ceiling wires are installed with low-velocity powder actuated tools in poured concrete deck. Includes 1-1/4 in. pin and clip. -
L.H. Dottie 1/4 x 2 in. Zinc Plated Steel Hex Head Cap Screws With Partial Thread
Grade 5 Hex Cap Screws are made from carbon steel and are used in applications where medium strength is necessary, typically those where controlled clamp force and high loads are required. These screws can be screwed into internally tapped holes or used with a nut. Grade 5 Hex Cap Screws should always be used with a hardened washer under the turned component. SAE J429 covers the material and performance requirements of Grade 5 Hex Cap Screws and ASME B18.2.1 covers the dimensional requirements. -
L.H. Dottie Sheet Metal Screw, Pan Head Phillips/Slotted (2-Way), Zinc Plated Steel, No. 10 x 1-1/4 in.
Sheet Metal Screws are a versatile fastener with specially hardened spaced threads and sharp points, and are capable of tapping their own internal threads. Typical applications for Sheet Metal Screws include fastening light metal sheets, wood, and plastic. They are manufactured with case hardened steel and finished with a zinc plating. ASME B18.3 covers the general requirements for the dimensions and performance of Steel Sheet Metal Screws.
