We use cookies to make your experience better.
To comply with the new e-Privacy directive, you agree to the privacy policy and our use of cookies.
Caddy (nVent)
Shop By
-
Caddy (nVent) Electrogalvanized Steel 1-Piece Strut Clamp For 0.72 to 1.16 in. O.D. Cable, 1 in. EMT or 3/4 in. Rigid Conduit
One-Piece Cable/Conduit Clamp With Protective BootNo Screws or Bolts to DropRequires Only a Screwdriver or Nutdriver for InstallationFits Into Open Side of Strut Channel -
Caddy (nVent) Steel Between-Stud Box Mounting Bracket
Supports electrical boxes, plaster rings or low voltage devices from one bracketMounts 1-1/2 or 2-1/8 in. deep boxesEliminates the need for an electrical box on low voltage applications -
Caddy (nVent) Caddy Mounting Bracket, Steel, Bendable, 2-Gang, Locking Screws
For low voltage Class 2 use onlyMounts any standard low voltage device in 1/2 to 1-1/4 in. wallsMakes wire ""fishing"" easier -
Caddy (nVent) Spring Steel Bottom-Mount Cable to Flange Clip For 14-4 to 10-3 MC/AC Cable and 5/16 thru 1/2 in. Flange
Compliant With NEC Article 300.4(d) Allowing Cable to be Positioned a Minimum of 1-1/4 in. From Face of StudCompliant With CEC Rule 12-618 For Support of MC/AC Cable -
Caddy (nVent) Bottom-Mount Cable to Flange Clip For 14-4 to 10-3 MC/AC Cable and 1/8 thru 1/4 in. Flange, Spring Steel
Compliant With NEC Article 300.4(d) Allowing Cable to be Positioned a Minimum of 1-1/4 in. From Face of Stud -
Caddy (nVent) Hammer-On Flange Clip, Bottom-Mount With Stud For 1/4 in. Rod and 5/16 thru 1/2 in. Flange, Spring Steel
Bottom-mount hammer-on flange clips are used to support pipe from beam flanges and require only a hammer to install. -
Caddy (nVent) Cable/Conduit Clip, EMT, Steel, 1 in., For Up to 1/4 in. Rod or Flange
Supports Conduit (EMT, Rigid, ENT, IMT, MC/AC and Aluminum) to Rods or FlangesAlso Used For: Flexible Metallic Tubing, Armored Cable, Portable Cables, Control Tubes, Communications Cable, etc.No Installation Tools RequiredNOTE: For Horizontal Application Only When Using Plain Rods -
Caddy (nVent) Easy Snap Grommet, Polyethylene 1.315 in. O.D., Pack of 100
Provides 360 Degree Protection For Cable, Conduit, Plumbing and Fire Sprinkler Plumbing in Metal StudsSnap One Grommet Into Standard 1-11/32 in. Field-Punched Hole or Snap Two Together Into Any Shape Factory-Punched Hole -
Caddy (nVent) Steel Standoff Deck Angle Bracket
Supports conduit or pipe 1-1/2 in. (38mm) under the roof decking to prevent potential damage from nails or screws. Meets the requirements of NEC Section 300.4(E). -
Caddy (nVent) MC/AC and Non Metallic Sheathed Cable Support, Pre-Galvanized Steel
Secures Cables 1-1/4 in. From Face of StudFlared Edges Prevent Damage to the Cable JacketHolds Up to (4) MC/AC Cables or (4) 12-3 Non-Metallic Sheathed Cables With GroundUnique Stop-Bend Design Helps Prevent Cables From Being Installed Too Far From Face of Stud
