We use cookies to make your experience better.
To comply with the new e-Privacy directive, you agree to the privacy policy and our use of cookies.
Caddy (nVent)
Shop By
-
Caddy (nVent) CADDY174 CAT HP J-Hook With Hammer-On Flange Clip, Swivel, 4 in. Max. Bundle Dia., 1/8 to 1/4 in. Flange
Requires Only a Hammer to InstallRotates 360 Degrees to Support Various Directional Runs of CableProvides Optimal Support For High-Performance Data Cable, Up to and Including Cat 5e, Cat 6, Cat 6A, Cat 7 and Fiber OpticProvides Superior Fill Capacity and Load Rating Over Most Other Non-Continuous Cable Support AlternativesRounded Edges on J-Hooks Provide Proper Bend Radius Support For High Performance Data CablesCost-Effective Alternative to Expensive Cable TrayComplies With EN 50174-2Meets ISO/IEC 14763-2, TIA 568-C and TIA 569-CNon-Continuous Supports May Not Exceed Spacing of 5 ft. (1.5m) Per TIA 569-C.9.7Cable Capacity is Calculated Based On a 70% Fill Rate -
Caddy (nVent) CADDY174 CAT HP J-Hook, Pre-Galvanized Steel, 1-5/16 in. Dia.
Provides Optimal Support For High-Performance Data Cable, Up to and Including Cat 5e, Cat 6, Cat 6A, Cat 7 and Fiber OpticRounded Edges on J-Hooks Provide Proper Bend Radius Support For High Performance Data CablesMultiple Color Options Aid in the Identification and Organization of the Pathway ApplicationProvides Superior Fill Capacity and Load Rating Over Most Other Non-Continuous Cable Support AlternativesTested According to DIN 4102-12Complies With EN 50174-2Meets ISO/IEC 14763-2, TIA 568-C and TIA 569-C -
Caddy (nVent) CADDY174 CABLECAT J-Hook 3/4 in. Dia., Assembled to 4Z34, 1/8 thru 3/8 in. Flange
Provide Proper Support of Category 5e, Category 6, Fiber Optic and InnerductCost-Effective Alternative to Expensive Cable TrayGalvanized Finish on J-Hooks Provides Smoother Cable Pull and Greater Corrosion Resistance -
Caddy (nVent) Internal Strut Beam Clamp
Flat Cover Design Keyhole Screw Slots on Flat Covers Knockouts on Wireway Sides Open Top Assembly With or Without Knockouts -
Caddy (nVent) Spring Steel Push In 1/2 in. EMT Conduit Clamp With 9/32 in. Plain Hole
Push-In Installation of ConduitEliminates Need For Offset Bending ConduitMay be Used For Either Vertical or Horizontal Installations -
Caddy (nVent) B18 Combination Box/Conduit Hanger With Screw for 1/2 or 3/4 in. EMT Conduit, Spring Steel
One Rivited Assembly For Electrical Box and Conduit SupportEliminates Need For Offset Bending Conduit66% Less Drop Wires (Rod/Wire Application)Delivers With NEC and CEC ComplianceFor Single and Multiple Runs of ConduitNEC 300.11 Requires Dedicated Drop Wire/Rod and EC311 -
Caddy (nVent) Spring Steel EM-M Series Conduit/Pipe to Flange Clip For 1/2 in. EMT or Rigid Conduit and 9/16 to 3/4 in. Flange
Used to Support Pipe From Beam FlangesPipe/Tube Clip Pivots a Full 360 DegreesAvailable With Conduit Clip Bottom Mounted or Side Mounted -
Caddy (nVent) H-PSM Series Conduit to Flange Clip for 1 in. EMT Conduit and 1/8 to 1/4 in. Flange, Spring Steel
Requires Only a Hammer to InstallAvailable For EMT, Rigid and Aluminum ConduitWill Pivot Thru 360 DegreesNOTE: Indicated Loads Are Ultimate and Should Not be Combined -
Caddy (nVent) Spring Steel EM-M Series Conduit/Pipe to Flange Clip For 1 in. EMT or Rigid Conduit and 5/16 to 1/2 in. Flange
Used to Support Pipe From Beam FlangesPipe/Tube Clip Pivots a Full 360 DegreesAvailable With Conduit Clip Bottom Mounted or Side Mounted
